BQPJV - G-10 ADHESIVE

Product Identification

Product ID:G-10 ADHESIVE
MSDS Date:04/01/1988
FSC:8040
NIIN:00N012591
MSDS Number: BQPJV

Responsible Party
GATES ENGINEERING CO.,INC.
100 S. WEST STREET
WILMINGTON, DE 19801
US

Emergency Phone: .....DISCONNECTED....

Info Phone: 302-656-9951 ....DISCONNECTED....

Preparer: ROBERT V KIDD

Cage: 88112

Contractor
GATES ENGINEERING CO.,INC.
WILMINGTON, DE 19801 US

Telephone: .....DISCONNECTED....

Cage: 88112

Ingredients

CARBON BLACK

CAS: 1333-86-4

RTECS: FF5800000

OSHA PEL 3.5 MG/M3

ACGIH TLV: 3.5 MG/M3


N-HEXANE

CAS: 110-54-3

RTECS: MN9275000

OSHA PEL 500 PPM

ACGIH TLV: 50 PPM; 9293

EPA Report Quantity: 1 LB

DOT Report Quantity: 1 LB


TOLUENE

CAS: 108-88-3

RTECS: XS5250000

OSHA PEL 200 PPM/150 STEL

ACGIH TLV: 50 PPM; 9293

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS


HYDROCARBON OIL (RESIDUAL OILS,HYDROTREATED)

CAS: 64742-57-0

OSHA PEL 5 MG/M3 (OIL MIST)

ACGIH TLV: 5 MG/M3 (OIL MIST)

Hazards

LD50 LC50 Mixture:N/K
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:SKIN CONTACT MAY CAUSE DEFATTING AND
LEAD TO DERMATITIS. INGESTION MAY CAUSE LIVER AND/OR KIDNEY DAMAGE.
REPEATED AND PROLONGED EXPOSURE TO SOLVENTS MAY CAUSE BRAIN AND
NERVOUS SYSTEM DAMAGE. CONCENTR ATING AND INHALING THE CONTENTS MAY
BE HARMFUL OR FATAL. NOTE: TOLUENE (CAS# 108-88-3) APPEARS ON THE
NAVY (SUP DATA)
Explanation of Carcinogenicity:NONE
Effects of Overexposure:EYES:MAY CAUSE IRRITATION. SKIN:N/K .
INGESTION:IRRITATES DIGESTIVE TRACT. INHALATION:MAY CAUSE
DIZZINESS, NAUSEA, INCOORDINATION AND UNCONSCIOUSNESS. MAY ALSO
CAUSE PULMONARY INJURY AND PO SSIBLY DEATH.
Medical Cond Aggravated by Exposure:ANY PRE-EXISTING SKIN,LUNG OR HEART
DISORDER.

First Aid

First Aid:EYES:FLUSH WITH LARGE AMOUNT OF WATER FOR AT LEAST 15
MINUTES.CONSULT A PHYSICIAN.SKIN:WASH THOROUGHLY WITH SOAP AND
WATER.INGESTION:DO NOT INDUCE VOMITING.GET MEDICAL
ATTENTION.INHALATION:REMOVE TO F RESH AIR.IF BREATHING STOPS,BEGIN
ARTIFICIAL RESPIRATION AND CONSULT A PHYSICIAN.

Fire Fighting

Flash Point Method:SCC
Flash Point:0F,-17.78C
Lower Limits:1.2%
Upper Limits:7.0%
Extinguishing Media:DRY CHEMICAL,CARBON DIOXIDE OR FOAM.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:EXTREMELY FLAMMABLE.VAPORS MAY IGNITE
EXPLOSIVELY/CAUSE FLASH FIRE.HAZARDOUS DECOMPOSITION
PRODUCTS:CARBON MONOXIDE AND SULFUR DIOXIDE.

Accidental Release

Spill Release Procedures:CONTAIN SPILL AND ABSORB ON SUITABLE MATERIAL.
Neutralizing Agent:N/K

Handling

Handling and Storage Precautions:KEEP AND STORE IN COOL,DRY PLACE AWAY
FROM SOURCES OF IGNITION.GROUND DURING TRANSFER.
Other Precautions:HARMFUL IF INHALED.

Exposure Controls

Respiratory Protection:WEAR AN APPROPRIATE,PROPERLY FITTED RESPIRATOR
(NIOSH/MSHA APPROVED) DURING AND AFTER APPLICATION UNLESS AIR
MONITORING DEMONSTRATES VAPOR/MIST LEVELS ARE BELOW APPLICABLE
LIMITS.
Ventilation:LOCAL EXHAUST AS NEEDED TO KEEP VAPOR/MIST LEVELS BELOW
APPLICABLE LIMITS.
Protective Gloves:RECOMMENDED.
Eye Protection:CHEM GOG/SFTY GLASSES W/ SIDE SHIELDS.
Other Protective Equipment:AVAILABILITY OF EYE WASHES AND SAFETY
SHOWERS IS RECOMMENDED.
Work Hygienic Practices:N/K
Supplemental Safety and Health
ROUTE OF ENTRY:INGEST ;SKIN (MFR). HEALTH HAZARDS: OCCUPATIONAL
REPRODUCTIVE HAZARDS LIST. SEEK CONSULTATION WITH APPROPRIATE
PROFESSIONALS CONCERNING LATEST HAZARD LIST INFORMATION AND SAFE
HAN DLING AND EXPOSURE RECOMMENDATIONS .

Chemical Properties

HCC:F2
Melt/Freeze Pt:M.P/F.P Text:N/K
Decomp Temp:Decomp Text:N/K
Vapor Density:>1 (AIR=1)
Spec Gravity:0.9 (WATER=1)
Evaporation Rate & Reference:<1 (ETHER=1)
Solubility in Water:INSOLUBLE
Appearance and Odor:BLACK,VISCOUS LIQUID WITH CHARACTERISTIC SOLVENT
ODOR.
Percent Volatiles by Volume:75

Stability

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:SPARKS,OPEN FLAMES OR HOT SURFACES.
Hazardous Decomposition Products:CARBON MONOXIDE AND SULFUR DIOXIDE.
Conditions to Avoid Polymerization:WILL NOT OCCUR.

Disposal

Waste Disposal Methods:DISPOSAL MUST BE IN ACCORDANCE WITH
FEDERAL,STATE AND LOCAL REGULATIONS .

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.